• Integrates both Raspberry Pi and Arduino platforms together
• Compatible with both 5v and 3v Arduino shields (selectable with jumpers)
• 32 bit ARM Cortex-M3 STM32F103 MCU 72MHz
• Free COOCOX downloadable software for ARM development
• Supports SPI, UART, I2C, PWM and CAN interface
• Support SWD/JTAG debugging and programming via the ISP interface
• Can be powered from USB or DC power supply (7-12VDC)

The Raspberry Pi Camera Module is a 5 megapixel custom designed add-on for Raspberry Pi, featuring a fixed focus lens. It's capable of 2592 x 1944 pixel static images, and also supports 1080p30, 720p60 and 640x480p60/90 video. It attaches to Pi by way of one of the small sockets on the board upper surface and uses the dedicated CSi interface, designed especially for interfacing to cameras.

The Pi-Face Digital is the first of a range of interfaces to allow the Raspberry Pi to control and manipulate the real world. It allows the Raspberry Pi to read switches connected to it – a door sensor or pressure pad perhaps, a microswitch or reed switch, or a hand held button. With appropriate easy to write code, the Raspberry Pi then drives outputs, powering motors, actuator, LEDs, light bulbs or anything you can imagine to respond to the inputs.

The Gert Board is designed to allow you to use your Raspberry Pi to drive motors to open doors, lift things, or power robotics. If you want to sense temperature and switch devices on and off; if you want to flash lights; if you want to teach it to play the glockenspiel; or if you want to learn about electronics from scratch, then Gertboard is for you.

The Gertboard comes preassembled and includes a user manual , which also acts as a teaching guide, bundled with plenty of programs to show you how to put things together.

You want to get hacking with your Pi fast, right? Get everything you need to start with the Adafruit Starter Pack for Raspberry Pi. It's the perfect accompaniment to your new Pi, everything you need to get a distro image loaded and running. We pre-assemble the Cobbler for you, no soldering required .

This kit does not contain a Raspberry Pi board

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy.

Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Plate from Adafruit, which can snap onto the Pi PCB (and is removable later if you wish) and gives you all sorts of prototyping goodness to make building on top of the Pi super easy.

We added lots of basic but essential goodies. First up, there's a big prototyping area, half of which is 'breadboard' style and half of which is 'perfboard' style so you can wire up DIP chips, sensors, and the like. Along the edges of the proto area, all the GPIO/I2C/SPI and power pins are broken out to 0.1" stips so you can easily connect to them. On the edges of the prototyping area, all of the breakout pins are also connected to labeled 3.5mm screw-terminal blocks. This makes it easy to semi-permanently wire in sensors, LEDs, etc. There's also a 4-block terminal block broken out to 0.1" pads for general non-GPIO wiring. Finally, we had a little space remaining over the metal connectors so we put in an SOIC surface mount chip breakout area, for those chips that dont come in DIP format.

Convienient small break out board for the Raspberry PI. XBee style connector for XRF / XBee / RN-XV / XBT / RF-BEE etc. Has the SPI and I2C pins on one standard 8 way header and the Raspberry PI's 8 general purpose I/O pins on another for easy access. Comes as a kit of parts that needs to be soldered. Construction is very easy and suitable for children with basic soldering skills.

A review of the board - http://www.doctormonk.com/2012/08/review-of-raspberry-pi-prototyping.html

Latest edition to the PI family of add-on's. It's the best and most useful prototyping board out on the market. Arranged with power down the middle and pads in groups of threes you'll find this much easier and faster to work with than other solutions.

Attach a Raspberry Pi computer to a plastic 'dish' with a full-sized breadboard.

An optimized collection of parts and pieces to experiment with Raspberry Pi at home, school or work. Great for students and those that want to get their feet wet, no soldering required!

This kit does not contain a Raspberry Pi board