MCM Electronics

SMD Remover Kit By Chip Quik (SMD 1) MCM Part #21-3450

5 stars 2 reviews

Safely removes SMDs using low heat. Fast and easy to use. Heat can be applied with a soldering iron, warm air pre-heater, or heat gun. The SMD is then easily removed with tweezers or a pick-up tool. Check out the attached video to see how easy it is!

Specifications Top

  • Low temperature desoldering alloy (136°F)
  • Syringe with no clean flux,and six alcohol pads
  • Product contents will remove 8-10 SMDs

  • Part Numbers
    MCM Part #:21-3450
    Chip Quik Part #:SMD 1
    Package Specifications & Dimensions
    Weight:0.0568 lbs.
    Warranty:1 days
    Need to Return?
    Length:4.5 in.
    Width:2.75 in.
    Height:1 in.
    Shipping Information
    Extra Shipping Charge:No
    Drop Ship:No

    Product Reviews Top

    • by pdaderko

      on 4/26/2014

      Does a great job, but not cheap

      Overall: 4.5 out of 5

      I really like this stuff... I've been using it occasionally for a few years, and it does exactly what it says it does. Just solder a glob of it across the pins of your chip, and the solder stays molten for a long time, giving you plenty of time to pull the chip. Personally, I prefer to use hot air for removing SMD components, but sometimes I'm worried about damaging the board, component, or other components around it with the hot air, so I go to the ChipQuik.

      The stuff isn't cheap, though my experience has been that you don't need a lot of it to do a chip, and that you can reuse it a few times before it becomes too diluted with real solder to be useful (solidifies too quickly). To reuse, I just touch it with the hot iron (without flux) and glob it up, and then I spread that on the next chip (with flux). You definitely need to remove any excess ChipQuik from the PCB pads (and parts, if you plan to reuse them) with desoldering braid before soldering again, but it cleans up easily.

      Though I don't use it a lot, it's money well spent to have it on hand for the times that I need it.

    • by atchisjd

      on 12/10/2012

      Good stuff

      Overall: 5 out of 5

      I've used ChipQuick for the last few years. Able to replace TSPO 66 memory IC with just a soldering iron! Just make sure to have some desolder braid to clean up the lands afterwards. I have not yet lifted a trace or land using this low temp alloy to remove SMD.

    Product Downloads Top

    PDF Reference

    Requires Adobe Acrobat Reader

    Associated Products

    Image of Soldapullt III Solder Remover

    21-210 - Soldapullt III Solder Remover

    Removes solder from soldered junctions Just heat solder, release inner prod and solder enters the tube

    In Stock


    Buy Now
    Image of Desoldering Pump

    21-8414 - Desoldering Pump

    Precision regulated return Replaceable tip Compact, anti-corrosive plastic housing Precision metal plunger Sealed vacuum chamber Easy cleaning

    In Stock


    Buy Now
    Image of Dual Helping Hand w/Sponge

    22-6475 - Dual Helping Hand w/Sponge

    •Enables user to keep both hands free for positioning, soldering, and assembly •Great for holding PC boards •Holds small parts in place while soldering •Adjusts to any position or angle

    In Stock


    Buy Now

    Others Also Bought

    32-31651 - 55120RE0110872LNA1-A1 Main Board

    55120RE0110872LNA1-A1 Main Board

    In Stock


    Buy Now

    RE5119C099-C702 - DVD Module

    DVD Module

    In Stock


    Buy Now
    Free Super Saver Shipping on orders over $39 for a Limited Time!
    Free Super Saver Shipping on orders over $39 for a Limited Time!