MCM Electronics

Hand-held Hot Air Rework ToolMCM Part #: 21-9220  |  Pro'skit Part #: SS-601A

Hand-held Hot Air Rework Tool 3.5 stars from 4 reviews.
Login to rate or review this product

  • CPU controlled rework tool precisely controls both temperature and air flow
  • Digital settings and visual display for full control
  • Space saving pencil design
  • Built-in fan for air control eliminates need for separate air pump
  • Can be used for QFP, SOP and PLCC SEM ICs

  • Product Description

  • Three different nozzles sizes included
  • Temperature adjustable from 212°F to 900°F
  • 110 Volt
  • 5~500 Watt

  • Product Reviews

    • "Works great but wish it remembered the last setting" by asarangan on 11/28/2014
      Overall: 3.5 out of 5

      Since it is a handheld tool, you have to turn it off every time you put it down. When you power it up, it doesn't remember the last temperature and fan speed. It starts from the lowest setting. It is easy to set these again, but it does get tiring after the one hundredth time. This is the most annoying aspect of this tool. Otherwise it works great.

    • "Works well for occasional use - but annoying to use" by mcmalistair on 7/31/2012
      Overall: 2.5 out of 5

      Runs smooth and heats quickly. Very annoying to use however as it does not remember the last settings and defaults to cold & slow fan speed. The result being between components, unless its left running all the time you spend a minute each time resetting the speed and heat. Good for occasional use but find something else if you are going to use it alot.

    • "Hot AIR Tool Review" by anteski on 12/29/2011
      Overall: 4 out of 5

      I just received This Hot Air Tool From MCM. Works Great If You Never worked with This Kind of equipment I would get A junk Board So you can get the hang of it. It has temp & air flow settings.And built heavy duty with digital readout which is Nice. I Am Happy With My Purchase.I Am a TV repair shop owner So saving $ on board repairs is Nice. Removed Surface Mount ics And Bridge Diodes.With No Problems. I recommend this product Highly!

    • "Works very well" by neilp92952 on 8/6/2009
      Overall: 4 out of 5

      After seeing this listed for several months, I bit the bullet and laid out the cash. Until now I was using a HeJet air gun, which would all too often blow other parts off the board, and could burn the board, as it had no temperature control I'm very pleased with the operation of this tool. The fan speed can be controlled to prevent blowing devices off the board, and the temperature control lets you apply just enough heat to melt the solder without burning the board. While it's a bit pricey, it can justify itself in the time saved by its use. I hope mine lasts a long time!

    • Rate It!

      Login Here to rate and review this product.

    Associated Products

    Image of Soldering Probe/Spudger/Pry Tool

    108-4054 - Soldering Probe/Spudger/Pry Tool

    The handy tool that frequently comes in handy. It can be used as a probe, scrapers, or spudger while soldering because of it's high heat tolerance. It can also be used to pry open laptops, iPods, cell phones, and other electronics without marking up the casing.

    In Stock


    Buy Now
    Image of SMD Remover Kit

    21-3450 - SMD Remover Kit

    Safely removes SMDs using low heat. Fast and easy to use. Heat can be applied with a soldering iron, warm air pre-heater, or heat gun. The SMD is then easily removed with tweezers or a pick-up tool.

    In Stock


    Buy Now
    Image of Siver Bearing Solder Paste - 7.1g Syringe

    21-8720 - Siver Bearing Solder Paste - 7.1g Syringe

    The no mess, no waste syringe works with the beat of a torch or lighter Flux is blended in and no additional flux is required Soldering bearing works great for electronics, wiring, connectors, and circuit boards

    In Stock


    Buy Now

    Others Also Bought

    Image of Double Sided Foam Tape

    28-955 - Double Sided Foam Tape

    •Thousands of uses •Fasten accessories to car dash, etc. •3/4" x 61/2' roll

    In Stock


    Buy Now
    Image of 10MM Headphones White High Performance Earbud

    35-5155 - 10MM Headphones White High Performance Earbud

    High Performance Earbud Headphones White Lightweight, stylish, high performance earbuds give crystal clear sound as well as a comfortable fit. Ideal for use with CD, MP3, MP4 and any other small portable audio players.

    In Stock


    Buy Now
    Image of VHS Head Cleaner

    80-6875 - VHS Head Cleaner

    VCR Head Cleaner safely and effectively cleans tape heads and entire tape path Non-abrasive Exclusive cleaning material prevents debris from re-depositing on heads Wet type

    In Stock


    Buy Now
    Package Specifications & Dimensions
    Weight:1.92 lbs.
    Warranty:90 days
    Need to Return?
    Length:11 in.
    Width:5.5 in.
    Height:3.25 in.
    Shipping Information
    Extra Shipping Charge:No
    Drop Ship:No
    Catalog Pages

    MCM Cat 57, Page 1145

    MCM Cat 56, Page 974

    Mfr. Info

    Pro'skit Logo
    Mfr. Name:Pro'skit
    Mfr. Part Number:SS-601A
    Save at least 15% on all Tenma Test Equipment through Sunday. Use promo code EMC396.
    Save at least 15% on all Tenma Test Equipment through Sunday. Use promo code EMC396.