MCM Electronics

1" Soft Dome Tweeter 30W RMSMCM Part #: 53-1080  |  MCM Audio Select Part #: 53-1080

1" Soft Dome Tweeter 30W RMS 3.8 stars from 9 reviews.
Login to rate or review this product

This high quality dome tweeter is perfect for repair, upgrade, or new speaker construction.

  • 30W/60W RMS/peak
  • Impedance: 8ohm
  • Sensitivity: 92dB
  • Frequency response: 1.5KHz~20KHz
  • Required cutout: 3" diameter plus notches for connectors
  • Mounting depth: 1¼"
  • Bolt pattern 3 3/8" d
  • Overall diameter: 4 1/16"

Product Reviews

  • "Awesome Dome tweeters" by ohmega1080 on 4/23/2014
    Overall: 5 out of 5
    Value:
    Quality:

    These Dome tweeters sound phenomenal. They are crisp and clear as it gets. I am using them in my ohm I series speakers that are 4 ways with 2 tweeters one facing forward and one facing up along with the midbass and midrange. Most of my drivers are from mcm. As far as the removable faceplates a lil black permatex #20-2983 applied before mounting will take care of that. Awesome dome tweeters.

  • "Nice tweeter for replacement or new projects - just use care when installing" by alanmaier on 10/4/2013
    Overall: 4.5 out of 5
    Value:
    Quality:

    These are a fantastic deal on a 1" dome tweeter. I've read the comments on breaking the bezel, and that is what prompted me to write this review. These do a really good job, they sound good and can extend low enough to be used in a 2 way system that - if you limit your power, can be crossed over fairly low. At this price you can improve power handling by making an array. You do need to realize that the bezel (face) is not attached to the tweeter by an adhesive. This works well as you can take them apart for fitting, and then use common sense when tightening these down. I've used many of these for rebuilds, and never broke one yet. Consider using thin sheet foam for a gasket - that will give you that needed seal without having to give them a tight "crunch".

  • "Solid performer" by dwayne.newton1 on 9/22/2012
    Overall: 4.5 out of 5
    Value:
    Quality:
    Top 25 Contributor

    These are a great value. Being suitable at an exceptionally low crossover point, these are ideal for a 2-way speaker system where the woofer has a limited upper range. The faceplate is removable but it's better to use it since it helps widen the dispersion from the dome. Some carefully applied contact cement will help keep it in place while working. Another reviewer mentioned the faceplate broke when putting in the screws, but didn't say whether the screws were round/panhead or the countersink type flathead screws. Don't use drywall or countersinking wood screws on this or it will likely cause damage. Using panhead screws that are screwed in until they are just tight enough should yield good results. They were packaged reasonably well. And the main thing is they sound pretty darned good.

  • "Really Poor Quality" by airtow on 4/25/2012
    Overall: 1 out of 5
    Value:
    Quality:

    Bought 2 of these and the front plate wasn't even attached, It appears they are just pushed onto the tweeter. Even if you wanted to glue them back on, they don't fit correctly. Plus the packaging is so minimal, that both came with the domes crushed. The axiom. You Get what you Pay For really applies here.

  • "Works Well" by circuithead on 1/27/2012
    Overall: 4 out of 5
    Value:
    Quality:

    Used these to replace some tweeters that sounded like they were going bad in a set 8" boxes. The highs seem a little clearer than the old tweeters and they look better than a 2" cone. I wish I would have been aware that the connection tabs are on the far edges of the tweeter frame though. Due to the tab locations I had to notch the openings in the boxes to get them to fit right.

  • "Both broke instantly" by nonsuchpro on 9/30/2011
    Overall: 1 out of 5
    Value:
    Quality:

    I hate to give bad reviews on anything but I have to on these. I bought a pair and as I screwed them in the plastic housing broke on both! Then each terminal post broke as I twisted on some wire just to test them before soldering. I just threw them in the trash. I never really even got to hear them properly. Don't waste your money on these.

  • "Excellent replacement performance in a home audio system" by mediaace on 8/27/2011
    Overall: 5 out of 5
    Value:
    Quality:

    I replaced a pair of original tweeters (physically identical) in a customer's 10" 3-way floor standing speakers with a 10" passive radiator. The customer was more than impressed that these offered better highs than the original set of tweeters. If I ever needed another set for another customer, I'd go right back to these!

  • "Good for the money!" by throatwarblermangrove on 5/2/2011
    Overall: 4 out of 5
    Value:
    Quality:

    I knocked a couple of stars off the quality rating because 2 of the four I purchased had broken faces. It appears that a light impact to the side of the packaging will fracture the somewhat-brittle plastic. The speakers are usable without the face, if rear mounted to a rounded over opening.I shouldn't have to go to all the extra work to do that, but it's not worth the postage to return them vs. their cost, which admittedly is a bargain. I'm using mine with 2 #55-2970 6.5" woofers in a MTM arrangement. Fun with cheap speakers!! Build something with these!

  • "Buy Them!" by tmacpcandaudio on 4/22/2011
    Overall: 5 out of 5
    Value:
    Quality:
    Top 25 Contributor

    Best value for this money of any tweeter I've ever used! I used these as a low cost way to upgrade the tweeters in my 02 intrepid's car stereo. With just a simple 6khz first order cap, these tweeters were crisp and balanced, and suitable for all kinds of music at medium-loud volume levels. I imagine with a 2nd order crossover they would handle even more power, and would be fine for any two or three way configuration. I imagine these are comparable to tweeters that five times as much. Buy them, right now! The only downside: they smell funny. No idea why, but after you've been handling them, they leave a strange smell on your fingers. No idea why.

  • Rate It!

    Login Here to rate and review this product.

Associated Products

Image of Acoustic Wadding Material

LS00385 - Acoustic Wadding Material

Made of white polyester fiber, this is perfect for internal speaker enclosure dampening, this wadding provides the perfect solution to eliminating problematic low frequency internal resonance. This material is a must for any speaker building or upgrade pro...

In Stock

$4.89

Buy Now

Others Also Bought

Image of 8

55-2971 - 8" Woofer with Poly Cone and Rubber Surround 70W RMS at 8ohm

8" Polypropylene Cone Woofer Low cost general replacement woofer is ideal in a two way cabinets or as a compact subwoofer. It is perfect for a wide variety of home or autosound applications and is ideal for either ported or sealed enclosures. Also available in ...

In Stock

$8.39

Buy Now
Image of DeoxIT D5 Spray Contact Cleaner, 5% solution, 5 oz.

200-040 - DeoxIT D5 Spray Contact Cleaner, 5% solution, 5 oz.

Fast acting deoxidizing solution cleans, improves conductivity, lubricates & protects. DeoxIT contact cleaner dissolves oxides and sulfides that form on metal surfaces. This restores the contact’s integrity and leaves a thin microscopic layer that protects t...

In Stock

$9.89

Buy Now
Image of Fuse Type Lamp - 8V .25A

25-090 - Fuse Type Lamp - 8V .25A

Voltage: 8.0V Current: 0.25A

In Stock

$0.84

Buy Now
Package Specifications & Dimensions
Weight:1.12 lbs.
Hazardous:Yes
RoHS Comp:Yes
Warranty:365 days
Need to Return?
Length:4.5 in.
Width:4.5 in.
Height:1.75 in.
Shipping Information
Extra Shipping Charge:No
Drop Ship:No
Catalog Pages
Catalog/Page:

MCM Cat 57, Page 178

PDF Reference
Datasheet

Requires Adobe Acrobat Reader.

Mfr. Info

MCM Audio Select Logo
Mfr. Name:MCM Audio Select
Mfr. Part Number:53-1080