MCM Electronics

4'' Aluminum Cone WooferMCM Part #: 55-1856  |  MCM Audio Select Part #: 55-1856

4'' Aluminum Cone Woofer 4.6 stars from 8 ratings and 7 reviews.
Login to rate or review this product

Versatile driver offers high power capacity and wide frequency response making it ideal in applications including full range and midbass in compact monitors. Large vented magnet, heavy duty voice coil and thick aluminum cone provide tremendous durability in high SPL applications.

Product Description

  • Aluminum cone
  • Synthetic dust cap
  • Rubber surround
  • Stamped steel basket
  • 1" copper voice coil
  • 17.7oz. magnet

    Specifications:
  • Power Capacity: 50W/100W RMS/peak
  • Sensitivity: 86dB (W/M)
  • Impedance: 8Ω
  • Re: 6.6Ω
  • Le: 0.48mH
  • Frequency response: 65Hz ~ 17KHz
  • Fs: 65Hz
  • Qts: 0.365
  • Qes: 0.436
  • Qms: 2.25
  • Vas: 3.15 (liters)
  • Xmax: 2.25mm
  • Overall frame diameter: 4.13" (pincushion)
  • Required cutout: 3.66"
  • Mounting depth: 2.5"

  • Product Reviews

    • "Nice sounding driver." by Klbird on 9/2/2014
      Overall: 3 out of 5
      Value:
      Quality:

      I used two of these parallel with a Dayton 4 ohm dome tweeter crossing at 3 Khz, in a transmission line tuned to 50 Hz. They produce amazing bass with low distortion. The mids are detailed and power handling is not a problem. Their performance far exceeds there low cost.

    • "a great driver--but could use some better packaging as the lips on the frame tend to bend" by litekeys on 7/31/2014
      Overall: 5 out of 5
      Value:
      Quality:

      These are great drivers and wonderful for the money. Almost world class IMHO.

      They should be used with a tweeter and need to be crossed over low pass (pick your frequency from 2kHz to 6kHz) so they do not deliver spurious output in the tweeter range polluting the tweeters output. But other than that hey have a really nice clean, crisp punchy output. Very easy to work with.

      My only negative comment is the thin lips on the pincushion frame bend easily and the boxes these come in are flimsy with no support (unlike many others of the same type from MCM) inside the box. I have used many cases of these, and often one, two or even three of the drivers in the case come with unusably bent frames. MCM has been good about replacing these. But I hope they will work with the manufacturer on better housing inside the small boxes, since we are only talking about an addition 1 to 2 cents in cardboard to better secure it.

    • "Minimus 7 replacement" by montekay on 9/25/2013
      Overall: 5 out of 5
      Value:
      Quality:

      I'm probably rating this prematurely, maybe after more testing I should update. I just ran some quick test comparing this to the old Radio Shack Minimus 7 original driver. This has a much flatter impedance curve, almost identical curve at resonance (80 Hz) which means Qts will be similar. (I can check the exact details on that later) Distortion is where this driver really shines over the original Minimus 7. The difference is pretty dramatic especially in higher harmonics. The original driver has significant distortion at least to the 5th and higher. With this driver harmonics above the 3rd are really low. Also the 2nd and 3rd are lower on this driver than the original. You don't need measurement equipment to know this one is considerably better than the original, it's immediately obvious just listening to the test tones. Time is always a problem for me. I will try to resist the urge to just get these into the Minimus boxes and not document anything. I need to make myself do a youtube video of the distortion measurements, LspCAD crossover development and any testing on the tweeter or replacement of the tweeter. Not promising this will happen but if it does I'll update this review with a link. This driver has just a bit more resonance peak issues at cone break up than the original which is expected of an aluminum cone. This will have to be dealt with in the new crossover design. I think this driver along with proper crossover redesign can make for a very noticeable improvement on any old Minimus 7's you may have laying around.

    • "Amazing Little Speaker" by kencary on 7/14/2013
      Overall: 5 out of 5
      Value:
      Quality:

      I used one of thes to replace a driver in an old die cast 2-way mini speaker and the results were amazing. If you close your eyes you'd think this was a speaker with an 8" woofer. The magnet is quite large and I had to modify the cabinet to fit, but the results were well worth it. Make sure you have room for the large ceramic magnet which is about 4" in diameter. I like this driver so much, that I am tempted to buy a few more to hold on to even though I don't have an immediate need. A great bargain. Well made, nice compliant rubber surround.

    • "very good 4" woofer" by showhorse on 12/24/2012
      Overall: 4 out of 5
      Value:
      Quality:

      An excellent replacement speaker. Good construction, larger magnent, and better cone material than OEM speaker that I replaced with this unit.

    • "Speaker Hobbiest" by MrAWallace on 5/14/2012
      Overall: 4.5 out of 5
      Value:
      Quality:

      The lows on this woofer is stunning for its size and power ratio, I have search and tested many 4" woofers at various prices. SB Acoustics, CSS, EJ Jordan, Wavecor, Peerless, TangBang, Morel, HiVi, and Dayton just to name some. I ported it in a .13 Ltr cabinet with a 1.25"D X 5.5"L flared tube paired with a 2.5" mid and a 1." tweeter, this baby is music to my ears on a budget!! It has to Xover pretty low, because the upper mids start getting muddy, this woofer probably should be listed as a subwoofer/low midwoofer.

    • "Exccellent replacement speaker!!!" by smokinjoe8 on 4/12/2012
      Overall: 5 out of 5
      Value:
      Quality:

      Bought 2 of these little Gems to replace worn out 4" ers from Boston Acoustics Sub Sat 6's. Dropped right in sounded better than the originals... Will be buying 2 more for another set of BA's that I have.. TOTALLY PLEASED...

    • Rate It!

      Login Here to rate and review this product.

    Others Also Bought

    Image of Indoor / Outdoor Speaker Pair 6.5

    50-8886 - Indoor / Outdoor Speaker Pair 6.5" 70V/8ohm - Black

    Indoor / Outdoor Speaker Pair (black) Rugged weatherproof speaker pair is designed to meet the needs of virtually any indoor or outdoor situation, in both residential whole-house systems and distributed commercial sound environments. They are ideal in large scale...

    In Stock

    $129.99

    Buy Now
    Image of 500ft 16AWG CMR In-Wall 2-Conductor Speaker Wire Black Box

    24-14115 - 500ft 16AWG CMR In-Wall 2-Conductor Speaker Wire Black Box

    500ft Standard 16/2 Inwall Speaker Wire with Black Jacket This 2-conductor CMR/CL2R rated speaker wire is ideal for various audio applications including whole-house and home theater.

    Limited Stock

    $92.00

    Buy Now
    Package Specifications & Dimensions
    Weight:2.2055 lbs.
    Hazardous:Yes
    Warranty:365 days
    Need to Return?
    Length:4.5 in.
    Width:4.5 in.
    Height:4 in.
    Shipping Information
    Extra Shipping Charge:No
    Drop Ship:No
    Catalog Pages
    Catalog/Page:

    MCM Cat 57, Page 167

    MCM Cat 56, Page 294

    PDF Reference
    Datasheet

    Requires Adobe Acrobat Reader.

    Mfr. Info

    MCM Audio Select Logo
    Mfr. Name:MCM Audio Select
    Mfr. Part Number:55-1856