MCM Electronics

PA / DJ Speaker Six Tweeter ArrayMCM Part #: 555-10345  |  MCM Custom Audio Part #: 555-10345

PA / DJ Speaker Six Tweeter Array 4.5 stars from 6 reviews.
Login to rate or review this product

Outstanding high frequency response, wide dispersion and very high immunity to burnout make this an ideal addition to any existing PA speaker system. Six-sided enclosure places six piezoelectric tweeters at five different angles for ultra wide dispersion. Because piezo tweeters have very high impedance at low frequencies, no crossover is required, and they may be connected directly in parallel with the existing speaker system.

Product Description

  • Power Capacity: 100W RMS
  • Frequency Response: 1KHz~16KHz
  • SPL: 89dB
  • Dimensions: 5.5" (H) x 19.5" (W) x 10" (D)
  • Inputs: ¼" input connection as well as binding posts

Product Reviews

  • "amazed and shock of" by hitme202020 on 3/24/2014
    Overall: 4 out of 5
    Value:
    Quality:

    I were amazed and shock of the frequency of these tweeters I used them at my church along with pair of 15 and 4 18 mcm subs with a old Crown ps 400 amp very amazed

  • "Good Sound, Great Value" by barry on 8/30/2012
    Overall: 5 out of 5
    Value:
    Quality:

    I ordered this tweeter to boost speech intelligibility on my home theater sound system. It works great. Well-built, no crossover needed, just hooked it in parallel with my center channel speaker. My wife and I are older and this helps bring out the dialogue in films with noisy backgrounds. It may add too much treble for some folks, but you can dial it back on your amplifier equalizer. Nice looking (if a tad larger than I would have liked) and we're pleased.

  • "Tweeter Array" by sycamoredave on 2/19/2012
    Overall: 4 out of 5
    Value:
    Quality:

    For the money, this is a nice product. We needed something to enhance and better disburse the high end in our Church sound system. It has sounded a bit muddy. Without adding a lot of volume, this has added the missing part. We do have to run it with a separate, appropriately powered amp, as these things won't take much power. Also, we are not sure how long they will last. Even if they don't last very long, the boxes are worth the money, and we can upgrade the tweeters.

  • "Better coverage for outdoor events" by Davisound on 10/9/2011
    Overall: 5 out of 5
    Value:
    Quality:
    Top 10 Contributor

    We added a pair of these to our 18" subs and pole mounted 12" two ways, trying to get wider coverage during our outdoor performances. Wow, what an improvement! Just ordered a second pair for our 15" subs with 10" pole mounts. Great product, keep up the good work!

  • "Great value" by tamaloud on 4/17/2011
    Overall: 4.5 out of 5
    Value:
    Quality:

    I bought a pair of these as I needed a wider dispersion than the tweeters I was using. Piezo's are inexpensive to start with but with 6 in a pretty sturdy cabinet I have been pleased with them so I ordered a second pair for a friend. In a studio rehearsal room they worked well where several people are in various places and could not always hear the high end well. The side drivers may not always be needed / wanted in a front of house PA setup. A simple matter to unhook those if needed by unscrewing the driver and disconnecting it.

  • "Spread the Highs around..." by CasperMilktoast on 7/6/2010
    Overall: 4.5 out of 5
    Value:
    Quality:

    I use a pair of these on top of a couple 15" 4-way Sound Reinforcement speakers I use by the poolside for parties. I power them all with 700 w/ch Amp. I use a jumper cable from my main speakers to the 1/4" jack on these tweeter boxes. Overall, they are a great value for the cost. I can't imagine building these for any less using raw components. The best part is, IF you happened to blow one (or more) of the 6 tweeters they are very easy to unscrew and replace if needed. The only complaints I have about them is they are not the highest SPL speakers out there for Piezo's and I had to open one box up (by removing a tweeter) so I could shake out some loose pieces that were rattling around inside the box that were dime-sized chunks of hard plastic. These units don't come with rubber feet but do have metal corners. If you plan to set them on hard wood bass cabinets you will need some feet or they will vibrate off. They do a great job at spreading the high frequencies around a large radius listening area.

  • Rate It!

    Login Here to rate and review this product.

Others Also Bought

Image of Universal Television Stand, For Televisions 32

50-14795 - Universal Television Stand, For Televisions 32" ~ 60"

Universal Television Stand Perfect for flat panel televisions that were mounted to the wall, but are to be moved to tabletop use. Universal mounting plate attaches to all VESA standard sets from 200x200 through 600x400, and provides a secure and attractive mount...

In Stock

$59.99

Buy Now
Image of Equipment Wall Bracket - Adjustable Length

50-14780 - Equipment Wall Bracket - Adjustable Length

White Equipment Wall Bracket Designed for supporting microwave ovens from the wall, this bracket is ideal for any type of equipment.

In Stock

$13.29

Buy Now
Image of Bracket Pole Mount VESA75/100

50-14534 - Bracket Pole Mount VESA75/100

Pole Mount Bracket for LCD Monitors Rugged bracket fits any 30mm ~ 60mm diameter pole, whether positioned horizontally or vertically. Great for use with PA speaker and light stands, lighting and stage trusses, and support masts. Pivoting mechanism allows monito...

In Stock

$20.39

Buy Now
Package Specifications & Dimensions
Weight:8 lbs.
Hazardous:No
RoHS Comp:Yes
Warranty:90 days
Need to Return?
Length:20.5 in.
Width:10.75 in.
Height:6 in.
Shipping Information
Extra Shipping Charge:No
Drop Ship:No
Catalog Pages
Catalog/Page:

MCM Cat 57, Page 027

MCM Cat 56, Page 190

Mfr. Info

MCM Custom Audio Logo
Mfr. Name:MCM Custom Audio
Mfr. Part Number:555-10345