MCM Electronics

Hand-held Hot Air Rework Tool By Pro'skit (SS-601A) MCM Part #21-9220

3.5 stars 4 reviews
$155.50 
MSRP: $171.05
You Save: $15.55 (9 %)

  • CPU controlled rework tool precisely controls both temperature and air flow
  • Digital settings and visual display for full control
  • Space saving pencil design
  • Built-in fan for air control eliminates need for separate air pump
  • Can be used for QFP, SOP and PLCC SEM ICs
  • Specifications Top

  • Three different nozzles sizes included
  • Temperature adjustable from 212°F to 900°F
  • 110 Volt
  • 5~500 Watt
    Part Numbers
    MCM Part #:21-9220
    Pro'skit Part #:SS-601A
    Package Specifications & Dimensions
    Weight:1.92 lbs.
    Hazardous:No
    Warranty:90 days
    Need to Return?
    Length:11 in.
    Width:5.5 in.
    Height:3.25 in.
    Shipping Information
    Extra Shipping Charge:No
    Drop Ship:No
  • Product Reviews Top

    • by asarangan

      on 11/28/2014

      Works great but wish it remembered the last setting

      Overall: 3.5 out of 5
      Value:
      Quality:

      Since it is a handheld tool, you have to turn it off every time you put it down. When you power it up, it doesn't remember the last temperature and fan speed. It starts from the lowest setting. It is easy to set these again, but it does get tiring after the one hundredth time. This is the most annoying aspect of this tool. Otherwise it works great.

    • by mcmalistair

      on 7/31/2012

      Works well for occasional use - but annoying to use

      Overall: 2.5 out of 5
      Value:
      Quality:

      Runs smooth and heats quickly. Very annoying to use however as it does not remember the last settings and defaults to cold & slow fan speed. The result being between components, unless its left running all the time you spend a minute each time resetting the speed and heat. Good for occasional use but find something else if you are going to use it alot.

    • by anteski

      on 12/29/2011

      Hot AIR Tool Review

      Overall: 4 out of 5
      Value:
      Quality:

      I just received This Hot Air Tool From MCM. Works Great If You Never worked with This Kind of equipment I would get A junk Board So you can get the hang of it. It has temp & air flow settings.And built heavy duty with digital readout which is Nice. I Am Happy With My Purchase.I Am a TV repair shop owner So saving $ on board repairs is Nice. Removed Surface Mount ics And Bridge Diodes.With No Problems. I recommend this product Highly!

    • by neilp92952

      on 8/6/2009

      Works very well

      Overall: 4 out of 5
      Value:
      Quality:

      After seeing this listed for several months, I bit the bullet and laid out the cash. Until now I was using a HeJet air gun, which would all too often blow other parts off the board, and could burn the board, as it had no temperature control I'm very pleased with the operation of this tool. The fan speed can be controlled to prevent blowing devices off the board, and the temperature control lets you apply just enough heat to melt the solder without burning the board. While it's a bit pricey, it can justify itself in the time saved by its use. I hope mine lasts a long time!

    Associated Products

    Image of Soldering Probe/Spudger/Pry Tool

    108-4054 - Soldering Probe/Spudger/Pry Tool

    The handy tool that frequently comes in handy. It can be used as a probe, scrapers, or spudger while soldering because of it's high heat tolerance. It can also be used to pry open laptops, iPods, cell phones, and other electronics without marking up the casing.

    In Stock

    $2.09

    Buy Now
    Image of SMD Remover Kit

    21-3450 - SMD Remover Kit

    Safely removes SMDs using low heat. Fast and easy to use. Heat can be applied with a soldering iron, warm air pre-heater, or heat gun. The SMD is then easily removed with tweezers or a pick-up tool. Check out the attached video to see how easy it is!

    In Stock

    $13.99

    Buy Now
    Image of Siver Bearing Solder Paste - 7.1g Syringe

    21-8720 - Siver Bearing Solder Paste - 7.1g Syringe

    The no mess, no waste syringe works with the beat of a torch or lighter Flux is blended in and no additional flux is required Soldering bearing works great for electronics, wiring, connectors, and circuit boards

    In Stock

    $5.99

    Buy Now

    Others Also Bought

    Image of 8 Way Isolated DMX Splitter - 3-Pin to 3-Pin

    555-20220 - 8 Way Isolated DMX Splitter - 3-Pin to 3-Pin

    8-Way Isolated DMX Splitter Eight way DMX splitter solves two basic limitations of DMX-512 control, cable distance and number of devices. Because each output is isolated and independently amplified, it also prevents faults on one branch from affecting others.

    In Stock

    $99.99

    Buy Now
    Image of Beaglebone Black Development Board

    83-16241 - Beaglebone Black Development Board

    The BeagleBone Black is a maker-focused single board computer powered by a 1GHz Sitara™ AM3358 ARM® Cortex™-A8 processor from Texas Instruments.

    In Stock

    $48.00

    Buy Now
    Image of Bracket Pole Mount VESA75/100

    50-14534 - Bracket Pole Mount VESA75/100

    Pole Mount Bracket for LCD Monitors Rugged bracket fits any 30mm ~ 60mm diameter pole, whether positioned horizontally or vertically. Great for use with PA speaker and light stands, lighting and stage trusses, and support masts. Pivoting mechanism allows monito...

    In Stock

    $20.39

    Buy Now